Difference between revisions of "Equipment"

Revision as of 12:14, 17 October 2012

Diy Light Animation Equipment This page contains links and info about the DLA equipment with all current hardware is based off of the Pixelnet and DMX standard.

Smart String / Pixelnet Section

Smart String Info

Nodes(Lights) Info & Order Chart

**SS Lights Info Chart and Ordering Links**
Light type	Input Side	Max # per SSC based on current draw	Approx Amps per Max Nodes	Links to purchase online Approx. Length (It can be shorter or longer)
Smart String Nodes Red +, Green - , Blue Data	Big Chip Side of Node	128	3.7975 29ma each	25ct String 5-7 ft	50ct String 12-14 ft	75ct String 19-21 ft	100ct String 26-28 ft	128ct String 33-35 ft
(Metal Backed) 3 50/50 Nodes Red +, Blue - , Green Data	DI	120	3.96 33ma each	Square
(Plastic rectangle) 50/50 Nodes Red +, Blue - , Green Data	DI	80	4.16 52ma each	Rectangle (Center Spacing 4.7", Wire between each 3.9", Total 7.8')
Rigid strips 30 50/50 Nodes Red +, Blue - , Green Data	Male 3 pin connector	4	Not Known Yet	Rigid
Flexible strips 13ft 50/50 nodes Red +, Green - , Blue Data	Arrows show direction	1 (120 nodes each)	approx 3.96 33ma each	Flexible
Accessories →				3 Conductor Cable	3 Conductor Connectors Chart Wire Color Changes
Accessories →				Cat5e Cable
DSC Light Order Chart Make sure whatever lights you buy for DSC it says Common Anode + and its 12 volts and 4 wires IP Waterproof rating system
Dumb String Nodes Red -, Green -, Blue - , Common + (yellow or white wire)		100	waterproof IP68	String from Ray Wu
Dumb Flexible Strips 5M (~16ft) Red -, Green -, Blue - , Common + (yellow or white wire)		300	not waterproof	Flexible Strip from two dogs light store
Dumb Flexible Strips 5M (~16ft) Red -, Green -, Blue - , Common + (yellow or white wire)		150	not waterproof IP65	Flexible Strip from ebay store

SSC Pipe Size Chart

Device

Pipe

Cap

Purchase Info

Pixelnet Smart String Controller (SSC)

1 inch 200 PSI PVC / Sch 20

or 1 1/4 inch Sch 40 PVC

Also, 1inch PVC Sch 40 CAP

or 1 1/4 caps for 1 1/4 PVC pipe

Hole sizes 15/64 for 3 wire connectors &

7/32 for the pigtails

Lowes - Pipe

1" PVC Pipe 10ft

or 1 1/4" PVC Pipe 10ft

Lowes - CAP (2 per controller)

1" PVC Cap

or 1 1/4" PVC Cap

Pixelnet Dumb String Controller (DSC)

200 PSI PVC / Sch 20

Library

Documents PixelNet Specification(draft) Smart String Power Requirements Smart String Node Documentation Smart String LSP 2.0 Setup Guide	PixelNet Hub DMX channel chart Online Chart PixelNet Channel Example E1.31 Draft Standard	Conductor Trigger User Manual Conductor SEQ file layout
Videos Smart String Demo 1 Smart String Demo 2(Program SSC with SS Utility) SS Lights Options Node Lineup Cutting Flexible Strip & Test Firmware	EtherDongle and Passive Hub Demo EtherDongle Demo Part 2 EtherDongle w/ Toys EtherDongle w/ Conductor Demo EtherDongle output DMX	Conductor Tutorial
Software SS Utility Setup 7-10-2011 Null Nodes	Vixen ver 2.1 Pixelnet output plugin (Put this file in the /plugin/output folder) Updated 7-10-2011
Academy info - pdfs, links and more 2012 Show Presentations

Diagrams

Pixelnet Hardware (RGB)

EtherDongle and Add on boards

Pixelnet EtherDongle

Device	Firmware	Checksum
EtherDongle	Pixelnet ver2	Pickit3 = XXXX
EtherDongle	DMX	Pickit3 = XXXX
Conductor	[ Pixelnet]	Pickit3 = XXXX
Conductor	[ DMX]	Pickit3 = XXXX
Slave	[ Pixelnet]	Pickit3 = XXXX
Slave	[ DMX]	Pickit3 = XXXX

NOTE: Only use the Pickit 3 utility and not MPLAB to program the firmware NOTE: DON'T USE THE 49.9K RESISTORS FROM THE FIRST COOP, RJ IS GETTING REPLACEMENTS. THEY SHOULD BE 49.9 OHM

Lynx Conductor EtherDongle Daughter Board

Function & Use
Assembly Manual
[ Mouser Direct]

Lynx Trigger Conductor Input Board

Function & Use
Assembly Manual
[ Mouser Direct]

Lynx Slave EtherDongle Daughter Board

Function & Use
Assembly Manual
[ Mouser Direct]

USB Dongle and Combiner

Pixelnet USB Dongle

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	613B	613B

NOTE: Not for use with DMX, See below for DMX firmware

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Put one of the files below in the Vixen /plugin/output folder

Lynx Combiner can be use with Ether or USB Dongles

Pixelnet Hubs

PixelNet 16 Port Active Hub

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	811E	8196

12v Option Kit

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
NOTE: POWER CONNECTORS: ALWAYS use the (3) 4 pin power connectors with the 24 pin connector

Failure to add the extra power connectors can/will damaged the PS 24 pin Connector and Hub from excess current

Pixelnet 16 Port Passive Hub

NOTE: POWER CONNECTORS: ALWAYS use the (3) 4 pin power connectors with the 24 pin connector

Failure to add the extra power connectors can/will damaged the PS 24 pin Connector and Hub from excess current

Pixelnet 4 Port Passive Hub

Features	16-Port Active	16-Port Passive	4-Port Passive
Choose Pixelnet Universe	Yes	Yes	No
Uses PC Power Supply	Yes	Yes	No
Regenerates Pixelnet Data	Yes	No	No
DMX Out	Yes	No	No

Pixelnet Controllers Smart and Dumb

Smart String Controller

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard 7-10-2011	E2EB	E363
Test	2EF2	2F6A

Test Firmware User Guide

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
To configure SSC SS Utility

Smart String Controller V2

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	19F3	1A6B

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
To configure SSC SS Utility

Smart String Controller V3

File:Rr.jpg

160px

Function & Use
Assembly Manual v3
[ Mouser Direct]
Max 4 amps
PIC24FJ32GA002

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	25E1	2659
Test	B4A3	B51B

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
To configure SSC SS Utility

The updated EXE file for the utility. Just find your folder that your SSC utility is in and replace the old one with this new file. When you run it then you should see the additional choice for grouping on the utility.

Dumb String Controller

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	8DA7	8E1F

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

DMX Section

DMX Info

Hooking up a DMX Universe

Hookup Diagrams showing DMX devices connected to a computer.

Equipment Errata

This page is for mods needed on released production boards from DLA.

Controller (Dimmers) Comparison Table

Controller	DMX	# Channels	On Board SSR	Wireless Pkg	LNT	Dimming	On Board Splitter	12v DC	120v AC	240 AC
Lynx Express	Yes	16	Yes	EX/RX or RX	Yes	Yes	Yes (1)**	No	Yes	Yes
Lynx Freestyle	Yes	128	No/SSR4	EX/RX wMod or RX	No	Yes	No	No	Yes	Yes
Lynx SSR4-DMX	Yes	4	Yes	EX/RX wMod or RX	No	Yes	No	No	Yes	No
Lynx MR-16	Yes	16	LED/MR16	EX/RX wMod or RX	No	Yes	No	Yes ***	No	No

Legend

LNT = Light Normalizing Technology. With the proper curves all lights turn on and dim at the same rate.
Need to know if Lynx hardware works in your region? Lynx Voltage Info

Asterisk Notes

** Two DMX outputs using wired input (Cat5) with ver 3 pcb and higher or

One DMX output (DMX Out2) if using the mounted EX/RX wireless module on ver 3 pcb and higher

*** MR16 is capable of handling up to 24 volt DC source power. Please place a heat sink on the 5 volt regulator.

Cases Chart

Lynx Device	Case Part#	Info	Purchase Info
Express Freestyle	CG-1500	Coax Demarcation Enclosure 12.25 X 12 X 5.25 Note: As of 8/2011, the manufacturer has changed the locations of the mounting bosses in the case. You may need to make an adapter plate or use alternate means of attaching your board to the case.	Cable Amplifiers CG-1500 DF Countryman Call 612-724-4400 to Order Sales Manager Duke McNaughton DIYLEDEXPRESS CG-1500 Excess Supply CG-1500 Radiant Holidays New Style CG-1500
MR-16 16 Channel DC Controller	CG-500	Coax Demarcation Enclosure 6.3 X 7.8 X 2	DIYLEDEXPRESS CG-500 Radiant Holidays CG-500
SSR4 Splitter PixelNet 4 Port Passive Hub	TA-200	Coax Demarcation Enclosure 3.75 x 3 x 1.5	DF Countryman Call 612-724-4400 to Order Sales Manager Duke McNaughton DIYLEDEXPRESS TA-200 Excess Supply TA-200 Radiant Holidays TA-200
USB Dongle V1 USB Dongle V2 Wireless TX V1 Wireless TX/RX V2	LP-35P	Choose Gray and put in the comments of the order "Make Sure it has the PCB bosses" No Studs	Polycase LP-35 If you call they will ship USPS at a much cheaper rate than UPS
Wireless RX V1	LP-51P	Choose Gray and put in the comments of the order "Make Sure it has the PCB bosses" No Studs	Polycase LP-51 If you call they will ship USPS at a much cheaper rate than UPS

DMX Hardware

Flood Light - Aether

DMX LED RGBW Flood/Spot Light

Pronunciation on Aether:

Ether \E"ther\ ([=e]"th[~e]r), n. [L. aether, Gr. a'iqh`r, fr. a'i`qein to light up, kindle, burn, blaze; akin to Skr. idh,

indh, and prob. to E. idle: cf. F. ['e]ther.] [Written also [ae]ther.]

Lynx Aether

4 Channel Light

Function & Use
Manual
PIC24FJ32GA002
Video Manual
- Part 1
- Part 2
- Part 3
- Part 4
- Part 5 - Case
Troubleshoot Videos
- Red LED on part 1
- Red LED on part 2
Mouser Direct
Solder Paste Part # SPE-0012
Lens Part Numbers
Graphics

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	A6F9	A771
Test	xxxx	xxxx

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Parts Legend
Program Start Address with Lynx Express Configuration Utility

Lynx Aether II

4 Channel Light

15 deg

22 deg

32 deg

Graphics
Aether II Prototype Demo

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	84D5	854D
Test	xxxx	xxxx

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Program Start Address with Lynx Address Utility
Power - 12 AC Outdoor Accent Light Transformer - Estimate 35 watts per Aether 2

Example Homedepot Transformer

Dimmers

Dimmer Info - Manual, Mouser Direct BOM (Bill Of Materials), Firmware and Checksum

Lynx Express

16 Channel

Function & Use
Assembly Manual v5
- Previous Assembly Manuals
Assembly Videos
- Part 1
- Part 2
Mouser Direct
Graphics
PIC24FJ32GA002

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	64C0	6538

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Lynx Freestyle

128 Channel Controller only

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	9AAF	9AAF

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

16 CH DC Controller (MR16)

16 Channel LED

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	90D4	90D4

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

SSR4

4 Channel SSR plus DMX option

Function & Use
Assembly Manual
- Previous Assembly Manual
Mouser Direct
Graphics
PIC18F1220 (SSR4 with DMX version)

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	9408	9408

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

DMX Wireless Devices

Wireless(TX/RX)Ver 2

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	1AED	1B65

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
NOTE 2: Its recommended to use 50ms for Wireless. YMMV

Express Receiver (EX/RX)Ver 2

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	1AED	1B65

Firmware 12-12-2010

Checksums

Pickit2 - 1AED

Pickit3 - 1B65

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Mod for other Controllers

DMX Devices

DMX Lynx USB Dongle

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	0A6F	0A6F

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

FTDI USB Driver

NOTE: Pixelnet firmware, See above for Lynx USB Dongle / Pixelnet|USB Dongle Pixelnet firmware

Splitter

Function & Use
Assembly Manual v3
- Previous Manual
Mouser Direct
Graphics
240v Transformer Digikey's p/n 567-1019-ND

Bobcat DMX Tester

Bobcat DMX Servo Controller

Aeon Clock

Aeon

Clock

Assembly Manual
Parts Ordering:
- Mouser Direct
- Order (1) of this part
- PCB from RJ
PIC24FJ32GA002

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	24EE	23C1

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Video

Discontinued Hardware

Lynx

16 Channel

Assembly Manual
Firmware 9E83

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Transmitter (TX) Ver 1

Checksums

Pickit2 - xxxx

Pickit3 - 475E

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Express Receiver (EX/RX)Ver 1

Checksums

Pickit2 - xxxx

Pickit3 - 5EEA

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Mod for other Controllers

Standalone Receiver (RX)Ver 1

Checksums

Pickit2 - xxxx

Pickit3 - 5EEA

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

@@ Line 204: / Line 204: @@
 *[[Manual EtherDongle|Assembly Manual v1]]
 *[ Mouser Direct]
-*PIC32MX795F512L
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC32MX795F512L]
 {| cellpadding = "2" cellspacing="0" boarder = "1"
@@ Line 280: / Line 280: @@
 *[[Dongle_Manual_v2|Assembly Manual v2]]
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=9eeb022092 Mouser Direct]
-*PIC18F2450
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F2450]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 324: / Line 324: @@
 *[[Manual SSHub|Assembly Manual v1]]
 *[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=fe854712c6 Mouser Direct]
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 405: / Line 405: @@
 *[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=db8acde08c Mouser Direct]
 *Max 4 amps
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 436: / Line 436: @@
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c5920dab12 Mouser Direct]
 *Max 4 amps
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 462: / Line 462: @@
 *[ Mouser Direct]
 *Max 4 amps
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 494: / Line 494: @@
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c1541bd77b Mouser Direct]
 *Max 4 amps
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 610: / Line 610: @@
 *[[AetherUse| Function & Use]]
 *[[Manual]]
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 *'''Video Manual'''
 **[http://www.vimeo.com/11860195 Part 1]
@@ Line 655: / Line 655: @@
 *[[AetherIIUse| Function & Use]]
 *[[Manual_AetherII|Assembly Manual]]
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 *[[media:a2-template.pdf|Aether II Template (PDF)]]
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=41f67017d7 Mouser Direct]
@@ Line 708: / Line 708: @@
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=e19c8724ea Mouser Direct]
 *[[Graphics#.23Express|Graphics]]
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 735: / Line 735: @@
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=28345fc9d2 Mouser Direct]
 *[[Graphics#.23Freestyle|Graphics]]
-*PIC18F2455
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F2455]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
 |-
@@ Line 760: / Line 760: @@
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=b7accb974d Mouser Direct]
 *[[Graphics#.23MR16|Graphics]]
-*PIC18F1220
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F1220]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
 |-
@@ Line 788: / Line 788: @@
 **[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=5250caa9af SSR4 with DMX]
 *[[Graphics#.23SSR4|Graphics]]
-*PIC18F1220 (SSR4 with DMX version)
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F1220 (SSR4 with DMX version)]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
 |-
@@ Line 815: / Line 815: @@
 *[[Manual_TX_RX2|Assembly Manual]]
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=f80a5a0d8b Mouser Direct]
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
 |-
@@ Line 839: / Line 839: @@
 *[[Manual EXRX|Assembly Manual]]
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=e622895153 Mouser Direct]
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 876: / Line 876: @@
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=9eeb022092 Mouser Direct]
 *[[Graphics#.23Dongle|Graphics]]
-*PIC18F2450
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F2450]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
 |-
@@ Line 909: / Line 909: @@
 *[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=8ABF3AEFB2 Mouser Direct (Tester)]
 *[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=0a8146d89a Mouser Direct (Wireless Tx)]
-*PIC18F24J10-I/SP (Tester)
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F24J10-I/SP (Tester)]
-*PIC24FJ32GA002 (Wireless)
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002 (Wireless)]
 *[http://diylightanimation.com/index.php?action=dlattach;topic=4279.0;attach=6804 Tester Firmware - starting channel is 256]
 *[http://diylightanimation.com/index.php?action=dlattach;topic=9528.0;attach=9481 Tester Firmware - starting channel is 1]
@@ Line 923: / Line 923: @@
 *[http://www.diylightanimation.com/wiki/images/8/8f/Bobcat_Servo_Schematic.pdf Schematic]
 *[http://diylightanimation.com/index.php?action=dlattach;topic=4835.0;attach=7108 Configuration Tool]
-*PIC18F23K20-I/SP
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F23K20-I/SP]
 |}
@@ Line 934: / Line 934: @@
 **[http://www.newark.com/maxim-integrated-products/ds32khz-dip/ic-crystal-osc-32-768khz-5-5v-14/dp/74C2865?Ntt=DS32KHZ/DIP '''Order (1) of this part''']
 **'''PCB from RJ'''
-*PIC24FJ32GA002
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
 |-

Difference between revisions of "Equipment"

Revision as of 12:14, 17 October 2012

Contents

Smart String / Pixelnet Section

Smart String Info

Nodes(Lights) Info & Order Chart

DSC Light Order Chart

SSC Pipe Size Chart

Library

Pixelnet Hardware (RGB)

EtherDongle and Add on boards

USB Dongle and Combiner

Pixelnet Hubs

Pixelnet Controllers Smart and Dumb

DMX Section

DMX Info

Hooking up a DMX Universe

Equipment Errata

Controller (Dimmers) Comparison Table

Cases Chart

DMX Hardware

Flood Light - Aether

Dimmers

DMX Wireless Devices

DMX Devices

Aeon Clock

Discontinued Hardware

Navigation menu

Personal tools

Namespaces

Variants

Views

Actions

Search

diylightanimation

other wiki pages

Tools