Difference between revisions of "Equipment"

Latest revision as of 15:09, 27 February 2024

Diy Light Animation Equipment This page contains links and info about the DLA equipment with all current hardware is based off of the Pixelnet and DMX standard.

Smart String / Pixelnet Section

Smart String Info

Nodes(Lights) Info & Order Chart

**SS Lights Info Chart and Ordering Links**
Light type	Input Side	Max # per SSC based on current draw	Approx Amps per Max Nodes	Links to purchase online Approx. Length (It can be shorter or longer)
Smart String Nodes Red +, Green - , Blue Data	Big Chip Side of Node	128	3.7975 29ma each	50ct String 12-14 ft	75ct String 19-21 ft	100ct String 26-28 ft	128ct String 33-35 ft
(Metal Backed) 3 50/50 Nodes Red +, Blue - , Green Data	DI	120	3.96 33ma each	Square
(Plastic rectangle) 50/50 Nodes Red +, Blue - , Green Data	DI	80	4.16 52ma each	Rectangle (Center Spacing 4.7", Wire between each 3.9", Total 7.8')
Rigid strips 30 50/50 Nodes Red +, Blue - , Green Data	Male 3 pin connector	4	Not Known Yet	Rigid
Flexible strips 13ft 50/50 nodes Red +, Green - , Blue Data	Arrows this way ---> Not this <---	1 (120 nodes each)	approx 3.96 33ma each	Flexible
Accessories →				3 Conductor Cable	3 Conductor Connectors Chart Wire Color Changes
Accessories →				Cat5e Cable

Compatible Node Chipset: SSC was designed for the TM1804 & TM1809 chipset. The SSC output speed is 800Khz and 12volts. The WS2811 might be compatible if the speed is correct. If the chipset has two speeds than normally its called "High Speed"

DSC Light Order Chart

Make sure whatever lights you buy for DSC it says Common Anode + and its 12 volts and 4 wires

IP Waterproof rating system

Light type	Max # per DSC based on current draw	WaterProof Rating	Links to purchase online
Dumb String Nodes Red -, Green -, Blue - , Common + (yellow or white wire)	100	waterproof IP68	String from Ray Wu
Dumb Flexible Strips 5M (~16ft) Red -, Green -, Blue - , Common + (yellow or white wire)	150	not waterproof IP65	Flexible Strip from ebay store

SSC/DSC Pipe Size Chart

Device

Pipe

Cap

Purchase Info

Pixelnet Smart String Controller (SSC)

1 inch 200 PSI PVC / Sch 20

or 1 1/4 inch Sch 40 PVC

Also, 1inch PVC Sch 40 CAP

or 1 1/4 caps for 1 1/4 PVC pipe

Hole sizes 15/64 for 3 wire connectors &

7/32 for the pigtails

Lowes - Pipe

1" PVC Pipe 10ft

or 1 1/4" PVC Pipe 10ft

Lowes - CAP (2 per controller)

1" PVC Cap

or 1 1/4" PVC Cap

Pixelnet Dumb String Controller (DSC)

200 PSI PVC / Sch 20 1 1/4 pipe works

Library

Documents PixelNet Specification(draft) Smart String Power Requirements Smart String Node Documentation Smart String LSP 2.0 Setup Guide	PixelNet Hub DMX channel chart Online Chart PixelNet Channel Example E1.31 2018 Standard	Conductor Trigger User Manual Conductor SEQ file layout
Videos Smart String Demo 1 Smart String Demo 2(Program SSC with SS Utility) SS Lights Options Node Lineup Cutting Flexible Strip & Test Firmware	EtherDongle and Passive Hub Demo EtherDongle Demo Part 2 EtherDongle w/ Toys EtherDongle w/ Conductor Demo EtherDongle output DMX	Conductor Tutorial
Software SS Utility Setup 7-10-2011 Null Nodes SS Utility Setup 9-30-2012 for SSC firmware ver 3+	Vixen ver 2.1 Pixelnet output plugin (Put this file in the /plugin/output folder) Updated 7-10-2011
Academy info - pdfs, links and more 2012 Show Presentations

Diagrams

Pixelnet Hardware (RGB)

EtherDongle and Add on boards

Pixelnet EtherDongle

Function & Use
Assembly Manual v1
Mouser Direct
magjack
Case w/o cutouts update case number 2/25/13

PIC32MX795F512L

Device	Firmware	Checksum
EtherDongle	Pixelnet ver2	Pickit3 = 0000
EtherDongle	Pixelnet universes 33-96 posted here
EtherDongle	DMX	Pickit3 = 0000
Conductor - Revised	Pixelnet v69	Pickit3 = 0000
	Pixelnet v72	Pickit3 = 0000
Conductor	Pixelnet	Pickit3 = 0000
Conductor	[ DMX]	Pickit3 = XXXX
Slave	[ Pixelnet]	Pickit3 = XXXX
Slave	[ DMX]	Pickit3 = XXXX

NOTE: Conductor Revised Firmware requires at least Control Panel V3 and Read over Lynx Conductor Operations Manual for setup of CF and all files needed
NOTE2: Only use the Pickit 3 utility and not MPLAB to program the firmware NOTE: DON'T USE THE 49.9K RESISTORS FROM THE FIRST COOP, RJ IS GETTING REPLACEMENTS. THEY SHOULD BE 49.9 OHM

Lynx Conductor EtherDongle Daughter Board

PDF Version

You also need one each of the following:

ETD Case cut out info:

Only Need the CF Socket if replacing a broken one.

CF Socket
Control Panel ver 3 Needed for Conductor-Revised firmware v69 and up
Control Panel ver 1.5
Compact Flash card reader for your computer - to add files and format CF
Android App for Conductor

You must download it with your phone to have it install.

Lynx Trigger Conductor Input Board

Function & Use
Assembly Manual
[ Mouser Direct]

Lynx Slave EtherDongle Daughter Board

Wireless option

Asus-330N info
Buy from Amazon
The Asus units are connected to the EtherDongle, just as if they were hard wired ethernet connections.

One per each, if you have multiple EtherDongles including slave units working together.

Its for timing marks only from EtherDongle with Conductor to other EtherDongles with Slave boards.

The show data (sequence) is on the slave units and the timing from the wireless keeps each one in sync.

The EtherDongle with Conductor has the whole show on it (sequence and audio, etc)

USB Dongle and Combiner and Splitter

Pixelnet USB Dongle

Firmware	Checksum
Firmware	Pickit2	Pickit3
Pixelnet	613B	613B

NOTE: Not for use with DMX, See below for DMX firmware

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Put one of the files below in the Vixen /plugin/output folder

Lynx Combiner can be use with Ether or USB Dongles

Pixelnet Splitter

Zeus & Pixelnet Hubs

See SSC Comparison Table for details on SSC/Zeus cable lengths and version differences.

PixelNet Zeus 16 String (SSCs & Hub)

Function & Use
Assembly Manual v2
Assembly Manual v1
Mouser Direct Ver1
Mouser Direct Ver2
PIC24F04KA200
Refer to the J1Sys Board Jumper Chart for programming options.

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	0020	0020

Zeus Version of Smart String Utility
NOTE: Do not use this version of the SSU with the Smart String Controllers (SSC) until their firmware has been updated. It will lock up the SSC and make them appear to be dead, due to the new color patterns

PixelNet Zeus 8 String (SSCs & Hub)

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	0020	0020

PixelNet 16 Port Active Hub

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	811E	8196

12v Option Kit

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
NOTE: POWER CONNECTORS: ALWAYS use the (3) 4 pin power connectors with the 24 pin connector

Failure to add the extra power connectors can/will damaged the PS 24 pin Connector and Hub from excess current

Pixelnet 16 Port Passive Hub

NOTE: POWER CONNECTORS: ALWAYS use the (3) 4 pin power connectors with the 24 pin connector

Failure to add the extra power connectors can/will damaged the PS 24 pin Connector and Hub from excess current

Pixelnet 4 Port Passive Hub

Note: For all items in this section (Zeus, Hubs, Power Supplies):

They typically get installed into a group24/Marine battery box from walmart.
Place PS in the bottom and then mount the board across the top usually mounted using the DIY method of your choice.
Seal up any vent holes on the top of the box.
Example but be free to adapt to your needs.

Features	16-Port Active	16-Port Passive	4-Port Passive	Pixelnet Splitter
Choose Pixelnet Universe	Yes	Yes	No	No
Uses PC Power Supply	Yes	Yes	No	No
Regenerates Pixelnet Data	Yes	No	No	Yes
DMX Out	Yes	No	No	No

Pixelnet Controllers Smart and Dumb

See SSC Comparison Table for details on SSC/Zeus cable lengths and version differences.

Smart String Controller

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard 7-10-2011	E2EB	E363
Test	2EF2	2F6A

Test Firmware User Guide

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
To configure SSC SS Utility

Smart String Controller V2

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	19F3	1A6B

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
To configure SSC SS Utility

NOTE 2: Do not use version 1 firmware on version 2 hardware. Doing so may damage the PIC.

Smart String Controller V3

PCB never released to the members. (skipped over to SSC V4)
Only the firmware released for mods on the SSCv1 & SSCv2
PIC24FJ32GA002

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	ECE8	ED60
Test	2180	21F8

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
To configure SSC SS Utility

The updated EXE file for the utility. Just find your folder that your SSC utility is in and replace the old one with this new file. When you run it then you should see the additional choice for grouping on the utility.

Smart String Controller V4

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	D8D3	D8D3
[ Test]	XXXX	XXXX

NOTE: Different PIC, Firmware is NOT COMPATIBLE with pervious versions of the SSC.
NOTE 2: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
To configure SSC SS Utility

The updated EXE file for the utility. Just find your folder that your SSC utility is in and replace the old one with this new file. When you run it then you should see the additional choice for grouping on the utility.

SSC v1 & v2 Mod

On the following image you will see two colored in lines I painted on to an image of the top of a SSC. This mod was designed to be totally on the top of the PCB to allow those with their SSC’s already enclosed in the PVC to do this easily. Just slide the PCB up out of the PVC as if you were going to update the firmware which you are going to do also.

It does not matter if it is a V1 or V2 PCB this mod is exactly the same.

The red mark is where you need to use a razor blade and cut the trace where it is. This is on the TOP of the PCB where the parts are. You will find the heavier trace located between the pins of the two resistors. Make sure you cut it well enough that it does not make connection any longer.

Then on the back of the PCB place a jumper wire where the Yellow line is drawn. Connect these points with a small light wire making sure it does not short anything else. Remember to take into account that when you flip the PCB over to do this that everything is mirror imaged on you. Once this is complete you may want to change the top resistor (V1 pcb is marked as 330, V2 is marked as 47) to in the range of 220 - 330 ohms. It will work with others that we have used but you will find this to be the best area to use. 330ohm is the one to use if you are building new.

Flash your SSC with the new firmware. The same firmware now works on both controller versions.

Make sure you use the new utility program that is provided to program your modified SSC's. You only have to replace the exe file with one provided no new installed needed.

RJ

Dumb String Controller

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	8DA7	8E1F
Test	8A47	8ABF

DMX Section

DMX Info

Hooking up a DMX Universe

Hookup Diagrams showing DMX devices connected to a computer.

Equipment Errata

This page is for mods needed on released production boards from DLA.

Controller (Dimmers) Comparison Table

|}

Controller	DMX	# Channels	On Board SSR	Wireless Pkg	LNT	Dimming	On Board Splitter	12v DC	120v AC	240 AC
Lynx Express	Yes	16	Yes	EX/RX or RX	Yes	Yes	Yes (1)**	No	Yes	Yes
Lynx Freestyle	Yes	128	No/SSR4	EX/RX wMod or RX	No	Yes	No	No	Yes	Yes
Lynx SSR4-DMX	Yes	4	Yes	EX/RX wMod or RX	No	Yes	No	No	Yes	No
Lynx MR-16	Yes	16	LED/MR16	EX/RX wMod or RX	No	Yes	No	Yes ***	No	No

Legend

LNT = Light Normalizing Technology. With the proper curves all lights turn on and dim at the same rate.
Need to know if Lynx hardware works in your region? Lynx Voltage Info

Asterisk Notes

** Two DMX outputs using wired input (Cat5) with ver 3 pcb and higher or

One DMX output (DMX Out2) if using the mounted EX/RX wireless module on ver 3 pcb and higher

*** MR16 is capable of handling up to 24 volt DC source power. Please place a heat sink on the 5 volt regulator.

Cases Chart

Lynx Device	Case Part#	Info	Purchase Info
Express Freestyle	CG-1500	Coax Demarcation Enclosure 12.25 X 12 X 5.25 Note: As of 8/2011, the manufacturer has changed the locations of the mounting bosses in the case. You may need to make an adapter plate or use alternate means of attaching your board to the case.	Cable Amplifiers CG-1500 DF Countryman Call 612-724-4400 to Order Sales Manager Duke McNaughton DIYLEDEXPRESS CG-1500 Excess Supply CG-1500 Radiant Holidays New Style CG-1500
MR-16 16 Channel DC Controller	CG-500	Coax Demarcation Enclosure 6.3 X 7.8 X 2	DIYLEDEXPRESS CG-500 Radiant Holidays CG-500
SSR4 Splitter PixelNet 4 Port Passive Hub	TA-200	Coax Demarcation Enclosure 3.75 x 3 x 1.5	DF Countryman Call 612-724-4400 to Order Sales Manager Duke McNaughton DIYLEDEXPRESS TA-200 Excess Supply TA-200 Radiant Holidays TA-200
USB Dongle V1 USB Dongle V2 Wireless TX V1 Wireless TX/RX V2	LP-35P	Choose Gray and put in the comments of the order "Make Sure it has the PCB bosses" No Studs	Polycase LP-35 If you call they will ship USPS at a much cheaper rate than UPS
Wireless RX V1	LP-51P	Choose Gray and put in the comments of the order "Make Sure it has the PCB bosses" No Studs	Polycase LP-51 If you call they will ship USPS at a much cheaper rate than UPS

DMX Hardware

Flood Light - Aether

DMX LED RGBW Flood/Spot Light

Pronunciation on Aether:

Ether \E"ther\ ([=e]"th[~e]r), n. [L. aether, Gr. a'iqh`r, fr. a'i`qein to light up, kindle, burn, blaze; akin to Skr. idh,

indh, and prob. to E. idle: cf. F. ['e]ther.] [Written also [ae]ther.]

Lynx Aether

4 Channel Light

Function & Use
Manual
PIC24FJ32GA002
Video Manual
- Part 1
- Part 2
- Part 3
- Part 4
- Part 5 - Case
Troubleshoot Videos
- Red LED on part 1
- Red LED on part 2
Mouser Direct
Solder Paste Part # SPE-0012
Lens Part Numbers
Graphics

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	A6F9	A771
Test	767D	76F5

Manual set channel = 2800
Must use Hexadecimal numbers
Example Start Channel 350 set Memory Location 2800 = 015E

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Parts Legend
Program Start Address with Lynx Express Configuration Utility

Lynx Aether II

4 Channel Light

Lens

15 deg

22 deg

32 deg

Graphics
Aether II Prototype Demo

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	84D5	854D
Test	78DD	7955

Manual set channel = 2800
Must use Hexadecimal numbers
Example Start Channel 125 set Memory Location 2800 = 007D

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Program Start Address with Lynx Address Utility
Power - 12 AC Outdoor Accent Light Transformer - Estimate 35 watts per Aether 2

Example Homedepot Transformer

Dimmers

Dimmer Info - Manual, Mouser Direct BOM (Bill Of Materials), Firmware and Checksum

Lynx Express

16 Channel

Function & Use
Assembly Manual v5
- Previous Assembly Manuals
Assembly Videos
- Part 1
- Part 2
NOTE: SAA1064 on BOM is no longer available; it must be sourced from eBay or the secondary market
Mouser Direct
Graphics
PIC24FJ32GA002

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	64C0	6538

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Lynx Freestyle

128 Channel Controller only

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	9AAF	9AAF

Manual set channel = EEPROM Data Area = Memory Location 02 & 04
Must use Hexadecimal numbers
Example 100 = 0X64 set Memory 02 = 64 and Memory 04 = 00
Numbers over 255 must be split
Example 410 = 0X19A set Memory 02 = FF and Memory 04 = 9B

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

16 CH DC Controller (MR16)

16 Channel LED

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	90D4	90D4
Low Power	A07D	A07D

Manual set channel = A00
Must use Hexadecimal numbers
Example Start Channel 312 set Memory Location A00 = 0138
Size = 4.25" x 4.75" x 1.25"

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

SSR4

4 Channel SSR plus DMX option

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	9408	9408

Manual set channel = A00
Must use Hexadecimal numbers
Example Start Channel 32 set Memory Location A00 = 0020

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

DMX Wireless Devices

Wireless(TX/RX)Ver 2

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	1AED	1B65

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
NOTE 2: Its recommended to use 50ms for Wireless. YMMV

Express Receiver (EX/RX)Ver 2

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	1AED	1B65

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Mod for other Controllers

DMX Devices

DMX Lynx USB Dongle

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	0A6F	0A6F

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

FTDI USB Driver

NOTE: Pixelnet firmware, See above for Lynx USB Dongle / Pixelnet|USB Dongle Pixelnet firmware

Splitter

Function & Use
Assembly Manual v3
- Previous Manual
Mouser Direct
Graphics
240v Transformer Digikey's p/n 567-1019-ND

Bobcat DMX Tester

Bobcat DMX Servo Controller

Panther DMX Player

NOTE: Only use V2 firmware on V2 boards.
NOTE: To download firmware right click on it and choose save as.

Aeon Clock

Aeon

Clock

Assembly Manual
Parts Ordering:
- Mouser Direct
- Order (1) of this part
- PCB from RJ
PIC24FJ32GA002

Firmware	Checksum
Firmware	Pickit2	Pickit3
Standard	24EE	23C1

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Video

Discontinued Hardware

Lynx

16 Channel

Assembly Manual
Firmware 9E83
Manual set channel = A00
Must use Hexadecimal numbers
Example Start Channel 61 set Memory Location A00 = 003D

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Transmitter (TX) Ver 1

Checksums

Pickit2 - 46E6

Pickit3 - 475E

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Express Receiver (EX/RX)Ver 1

Checksums

Pickit2 - 5E72

Pickit3 - 5EEA

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Mod for other Controllers

Standalone Receiver (RX)Ver 1

Checksums

Pickit2 - 5E72

Pickit3 - 5EEA

NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware

Difference between revisions of "Equipment"

Latest revision as of 15:09, 27 February 2024

Contents

Smart String / Pixelnet Section

Smart String Info

Nodes(Lights) Info & Order Chart

DSC Light Order Chart

SSC/DSC Pipe Size Chart

Library

Pixelnet Hardware (RGB)

EtherDongle and Add on boards

USB Dongle and Combiner and Splitter

Zeus & Pixelnet Hubs

Pixelnet Controllers Smart and Dumb

DMX Section

DMX Info

Hooking up a DMX Universe

Equipment Errata

Controller (Dimmers) Comparison Table

Cases Chart

DMX Hardware

Flood Light - Aether

Dimmers

DMX Wireless Devices

DMX Devices

Aeon Clock

Discontinued Hardware

Navigation menu

Personal tools

Namespaces

Variants

Views

Actions

Search

diylightanimation

other wiki pages

Tools

@@ Line 23: / Line 23: @@
 |3.7975
 :29ma each
-|[http://www.aliexpress.com/fm-store/701799/209889132-495657082/25-node-LED-pixel-string-DC12V-input-new-model-IP68.html 25ct String]
-:5-7 ft
 |[http://www.aliexpress.com/fm-store/701799/209889132-495657175/50-node-LED-pixel-string-DC12V-input-new-model-IP68.html 50ct String]
 :12-14 ft
@@ Line 59: / Line 57: @@
 |Flexible strips 13ft 50/50 nodes
 :<font color="red">Red +</font>, <font color="green">Green '''-'''</font> , <font color="blue">Blue Data</font>
-|Arrows show direction
+|Arrows this way   --->
+:Not this  <---
 |<center>1 (120 nodes each)</center>
 |approx 3.96
@@ Line 66: / Line 65: @@
 |-
 |colspan="4" rowspan="2" align="center"|'''<font font size="4" color="red">A</font><font  font size="4" color="green">c</font><font  font size="4" color="blue">c</font><font  font size="4" color="red">e</font><font  font size="4" color="green">s</font><font  font size="4" color="blue">s</font><font  font size="4" color="red">o</font><font  font size="4" color="green">r</font><font  font size="4" color="blue">i</font><font  font size="4" color="red">e</font><font  font size="4" color="green">s</font> <font size="4" color="blue">&rarr;</font>'''
-|[http://www.aliexpress.com/fm-store/701799/210128048-425559947/100m-lot-3pin-cable-for-RGB-color-led-strip-module-20AWG-100m-long.html 3 Conductor Cable]
+|[https://www.aliexpress.com/store/product/50m-lot-3pin-RGB-18AWG-cable-for-led-pixel-module/701799_623994646.html?spm=2114.12010615.8148356.9.6c8f7ca2T7P0en 3 Conductor Cable]
 |colspan="4"|[http://www.aliexpress.com/fm-store/701799/209889132-425563008/10pcs-lot3-Core-White-Waterproof-Line-15cm-long-each-male-and-female.html 3 Conductor Connectors]
 [[3_Conductor|Chart Wire Color Changes]]
@@ Line 73: / Line 72: @@
 |-
 |colspan="9"  align="center"|
-== '''<font color="red">'''D'''</font><font color="green">'''S'''</font><font color="blue">'''C'''</font> Light Order Chart''' ==
+|-
+|colspan="14" align="center"|Compatible Node Chipset: SSC was designed for the TM1804 & TM1809 chipset. The SSC output speed is 800Khz and 12volts.
+The WS2811 might be compatible if the speed is correct. If the chipset has two speeds than normally its called "High Speed"
+|-
+|}
+<br>
+==== <font color="red">'''D'''</font><font color="green">'''S'''</font><font color="blue">'''C'''</font> '''Light Order Chart''' ====
 :'''Make sure whatever lights you buy for DSC it says Common Anode + and its 12 volts and 4 wires'''
 :[http://www.mpl.ch/info/IPratings.html '''IP Waterproof rating system''']
+{|cellpadding="5" cellspacing="0" border="1"
+|'''Light type'''
+|'''Max # per DSC'''
+:'''based on current draw'''
+|'''WaterProof Rating'''
+|colspan="5"|'''Links to purchase online'''
 |-
 |Dumb String Nodes
 :<font color="red">Red -</font>, <font color="green">Green -, <font color="blue">Blue '''-'''</font> , <font color="black">Common + (yellow or white wire)</font>
-|
 |<center>100</center>
 |waterproof IP68
@@ Line 88: / Line 100: @@
 |Dumb Flexible Strips 5M (~16ft)
 :<font color="red">Red -</font>, <font color="green">Green -, <font color="blue">Blue '''-'''</font> , <font color="black">Common + (yellow or white wire)</font>
-|
-|<center>300</center>
-|not waterproof
-|colspan="5"|[http://www.twodoglightstore.com/product.php?id_product=50 Flexible Strip] from two dogs light store
-|-
-|Dumb Flexible Strips 5M (~16ft)
-:<font color="red">Red -</font>, <font color="green">Green -, <font color="blue">Blue '''-'''</font> , <font color="black">Common + (yellow or white wire)</font>
-|
 |<center>150</center>
 |not waterproof IP65
@@ Line 106: / Line 109: @@
 <br>
-===='''SSC Pipe Size Chart'''====
+===='''SSC/DSC Pipe Size Chart'''====
 {| cellpadding="5" cellspacing="0" border="1"
 |-
@@ Line 138: / Line 141: @@
 |}
-====Library====
+===='''Library'''====
 {|cellpadding="5" cellspacing="0" border="0"
 |-
@@ Line 149: / Line 152: @@
 *[http://diylightanimation.com/index.php?action=dlattach;topic=5120.0;attach=6009 '''PixelNet Hub DMX channel chart'''] [[ChannelChart|'''Online Chart''']]
 *[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=6084 '''PixelNet Channel Example''']
-*[http://www.diylightanimation.com/wiki/index.php?title=media:E1-31r3.pdf '''E1.31 Draft Standard''']
+*[http://www.diylightanimation.com/wiki/index.php?title=media:ANSI_E1_31_2018.pdf '''E1.31 2018 Standard''']
 |
@@ Line 174: / Line 177: @@
 |'''Software'''
 *[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=6366 '''SS Utility Setup 7-10-2011'''] Null Nodes
+*[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=11435 '''SS Utility Setup 9-30-2012'''] for SSC firmware ver 3+
 |
 *[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=6342 '''Vixen ver 2.1 Pixelnet output plugin''']
@@ Line 195: / Line 199: @@
 |}
-===Pixelnet Hardware (RGB)===
+==='''Pixelnet Hardware (RGB)'''===
 ===='''EtherDongle and Add on boards'''====
 {| cellpadding="15" cellspacing="0" border="1"
@@ Line 203: / Line 207: @@
 *[[EtherDongleUse| Function & Use]]
 *[[Manual EtherDongle|Assembly Manual v1]]
-*[ Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=4bc0aa56f2 Mouser Direct]
+*[http://www.newark.com/jsp/search/productdetail.jsp?SKU=24M7451&CMP=AFC-OPH&CMP=AFC-OPH magjack]
+*[http://www.polycase.com/lp-70f Case w/o cutouts] update case number 2/25/13
 *PIC32MX795F512L
 {| cellpadding = "2" cellspacing="0" boarder = "1"
 |-
-|'''Device'''
+|width="20%"|'''Device'''
-|'''Firmware'''
+|width="30%"|'''Firmware'''
-|'''Checksum'''
+|width="30%"|'''Checksum'''
 |-
 |EtherDongle
 |[http://diylightanimation.com/index.php?action=dlattach;topic=5765.0;attach=7980 Pixelnet ver2]
 |Pickit3 = 0000
-|-
+|- valign="top"
+|EtherDongle
+|[http://diylightanimation.com/index.php?topic=8289.msg118440#msg118440 Pixelnet universes 33-96 posted here]
 |- valign="top"
 |EtherDongle
 |[http://diylightanimation.com/index.php?action=dlattach;topic=5765.0;attach=7397 DMX]
+|Pickit3 = 0000
+|-
+|<font color="Green">'''Conductor - Revised''' </font>
+|[http://diylightanimation.com/index.php?action=dlattach;topic=11905.0;attach=11694 Pixelnet v69]
+|Pickit3 = 0000
+|-
+|
+|[http://diylightanimation.com/index.php?action=dlattach;topic=13457.0;attach=12951 Pixelnet v72]
 |Pickit3 = 0000
 |-
 |Conductor
-|[ Pixelnet]
+|[http://diylightanimation.com/index.php?action=dlattach;topic=5767.0;attach=9893 Pixelnet]
-|Pickit3 = XXXX
+|Pickit3 = 0000
 |-
@@ Line 244: / Line 263: @@
 *[http://diylightanimation.com/index.php?action=dlattach;topic=5765.0;attach=6924 Vixen v2.1 Plugin for DMX firmware]
+'''NOTE:'''<font color=Green> '''Conductor Revised Firmware requires at least Control Panel V3 and Read over Lynx Conductor Operations Manual for setup of CF and all files needed''' </font>
-'''NOTE:''' Only use the Pickit 3 utility and not MPLAB to program the firmware
+<br>
+'''NOTE2:''' Only use the Pickit 3 utility and not MPLAB to program the firmware
 <font color="red">'''NOTE: DON'T USE THE 49.9K RESISTORS FROM THE FIRST COOP, RJ IS GETTING REPLACEMENTS. THEY SHOULD BE 49.9 OHM'''</font>
 |width="25%"|<center>'''Lynx Conductor'''</center>
-<center>'''EtherDongle Daughter Board'''</center>[[Image:Cond-10.jpg|right|thumb|160px]]
+<center>'''EtherDongle Daughter Board'''</center>[[Image:Cond-10.jpg|center|thumb|200px]]
 *[[ConductorUse| Function & Use]]
+*[[LCOM|Conductor Operations Manual]]
+::[http://diylightanimation.com/index.php?action=dlattach;topic=11905.0;attach=11686| PDF Version]
 *[[Manual_Conductor|Assembly Manual]]
-*[ Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=800fa0bd2d Mouser Direct]
+You also need one each of the following:
+*[https://www.sparkfun.com/products/9943 MP3]
+*[https://www.sparkfun.com/products/10160 RTC]
+*[https://www.sparkfun.com/products/337 Battery]
+*[https://www.sparkfun.com/products/116 Header]
+*[http://www.amazon.com/Kingston-CompactFlash-Memory-CF-8GB-S2/dp/B000Y138EK/ref=sr_1_6?ie=UTF8&qid=1347838625&sr=8-6&keywords=cf+card+8gb CF]
+<br>
+'''ETD Case cut out info:'''
+*[http://diylightanimation.com/index.php?action=dlattach;topic=11579.0;attach=11263 Case Cut Out Drawings]
+*[http://diylightanimation.com/index.php?action=dlattach;topic=11579.0;attach=11264 PolyCase Drawing #1]
+*[http://diylightanimation.com/index.php?action=dlattach;topic=11579.0;attach=11265 PolyCase Drawing #2]
+Only Need the CF Socket if replacing a broken one.
+*[http://www.mouser.com/ProductDetail/3M-Electronic-Solutions-Division/N7E50-M516RB-50-WF/?qs=sGAEpiMZZMvMXbh32ZmHAD/E31klPgN1 CF Socket]
+*[http://diylightanimation.com/index.php?action=dlattach;topic=11905.0;attach=11695 Control Panel ver 3] <font color="Green"> '''Needed for Conductor-Revised firmware v69 and up'''</font>
+*[http://diylightanimation.com/index.php?action=dlattach;topic=5767.0;attach=9894 Control Panel ver 1.5]
+*Compact Flash card reader for your computer - to add files and format CF
+*[http://diylightanimation.com/index.php?action=dlattach;topic=10074.0;attach=11128 Android App for Conductor]
+:You must download it with your phone to have it install.
 |width="25%"|<center>'''Lynx Trigger'''</center>
-<center>'''Conductor Input Board'''</center>[[Image:Trigger2.jpg|right|thumb|160px]]
+<center>'''Conductor Input Board'''</center>[[Image:Trigger2.jpg|center|thumb|200px]]
 *[[ConductorUse| Function & Use]]
 *[[Manual_Trigger|Assembly Manual]]
 *[ Mouser Direct]
 |width="25%"|<center>'''Lynx Slave'''</center>
-<center>'''EtherDongle Daughter Board'''</center>[[Image:Cond-4.jpg|right|thumb|160px]]
+<center>'''EtherDongle Daughter Board'''</center>[[Image:Cond-4.jpg|center|thumb|200px]]
 *[[ConductorUse| Function & Use]]
 *[[Manual_Slave|Assembly Manual]]
 *[ Mouser Direct]
+*[http://www.mouser.com/ProductDetail/3M-Electronic-Solutions-Division/N7E50-M516RB-50-WF/?qs=sGAEpiMZZMvMXbh32ZmHAD/E31klPgN1 CF Socket]
 |-
 |colspan="4"|'''Wireless option'''
@@ Line 280: / Line 319: @@
 <br>
-===='''USB Dongle and Combiner'''====
+===='''USB Dongle and Combiner and Splitter'''====
 {| cellpadding="15" cellspacing="0" border="1"
 |-
@@ Line 287: / Line 326: @@
 *[[USBPixelnetDongleUse| Function & Use]]
 *[[Dongle_Manual_v2|Assembly Manual v2]]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=9eeb022092 Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=3e72e3c7a8 Mouser Direct]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F2450]
@@ Line 299: / Line 338: @@
 |-
-|[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=6049 Standard]
+|[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=6049 Pixelnet]
 |613B
 |613B
@@ Line 319: / Line 358: @@
 *[[Manual_Combiner|Assembly Manual v1]]
 *[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=086313f476 Mouser Direct]
-|
+|width="25%"|<center>'''Pixelnet Splitter'''</center>
+[[Image:pixelnet splitter ics.jpg|right|thumb|160px]]
+*[[PixelnetSplitterUse| Function & Use]]
+*[[Manual_PixelnetSplitter|Assembly Manual v1]]
+*[http://www.diylightanimation.com/wiki/images/d/d5/Pixelnet_splitter.pdf Schematic]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=b1d794e2e3  Mouser Direct]|
 |
 |}
 <br>
-===='''Pixelnet Hubs'''====
+===='''Zeus & Pixelnet Hubs'''====
+''See [[SSC_Comparison|SSC Comparison Table]] for details on SSC/Zeus cable lengths and version differences.
 {| cellpadding="15" cellspacing="0" border="1"
 |-
+|- valign="top"
+|width="25%"|<center>'''PixelNet Zeus 16 String (SSCs & Hub)'''</center>[[Image:z16v2-15.jpg|right|thumb|160px]]
+*[[ZeusUse| Function & Use]]
+*[[Manual Zeus-v2|Assembly Manual v2]]
+*[[Manual Zeus|Assembly Manual v1]]
+*[https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=92006b8e92 Mouser Direct Ver1]
+*[https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=fdfb67e65c Mouser Direct Ver2]
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24F04KA200]
+*Refer to the [http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart J1Sys Board Jumper Chart] for programming options.
+{| cellpadding = "2" cellspacing="2" boarder = "1"
+|-
+|rowspan="2"|'''Firmware'''
+|colspan="2" align="center"|'''Checksum'''
+|-
+|width="10%"|'''Pickit2'''
+|width="10%"|'''Pickit3'''
+|-
+|[http://diylightanimation.com/index.php?action=dlattach;topic=11564.0;attach=12580 Standard]
+|0020
+|0020
+|}
+*[http://diylightanimation.com/index.php?action=dlattach;topic=12929.0;attach=12614 Zeus Version of Smart String Utility]
+*<font color="red">'''NOTE: Do not use this version of the SSU with the Smart String Controllers (SSC) until their firmware has been updated. It will lock up the SSC and make them appear to be dead, due to the new color patterns'''</font>
+|width="25%"|<center>'''PixelNet Zeus 8 String (SSCs & Hub)'''</center>[[Image:Zeus8-Fin.jpg|right|thumb|160px]]
+*[[Zeus8Use| Function & Use]]
+*[[Manual Zeus8|Assembly Manual v1]]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=a83fda054c Mouser Direct]
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24F04KA200]
+{| cellpadding = "2" cellspacing="2" boarder = "1"
+|-
+|rowspan="2"|'''Firmware'''
+|colspan="2" align="center"|'''Checksum'''
+|-
+|width="10%"|'''Pickit2'''
+|width="10%"|'''Pickit3'''
+|-
+|[http://diylightanimation.com/index.php?action=dlattach;topic=11564.0;attach=12580 Standard]
+|0020
+|0020
+|}
+|
+|
 |- valign="top"
 |width="25%"|<center>'''PixelNet 16 Port Active Hub'''</center>[[Image:Hub-Finished2.jpg|right|thumb|160px]]
 *[[ActiveHub16Use| Function & Use]]
 *[[Manual SSHub|Assembly Manual v1]]
-*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=fe854712c6 Mouser Direct]
+*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=5b6a7bc5e2 Mouser Direct]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
@@ Line 358: / Line 454: @@
 *[[PassiveHub16Use| Function & Use]]
 *[[Manual_PassiveHub16|Assembly Manual v1]]
-*[https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=6738b7ab36  Mouser Direct]
+*[https://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=94f0413013 Mouser Direct]
 <br>
 <font color="red">'''NOTE: POWER CONNECTORS: ALWAYS use the (3) 4 pin power connectors with the 24 pin connector'''</font>
@@ Line 368: / Line 464: @@
 *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=1fae9536c0  Mouser Direct]
 |
+<font color='red'>'''Note:''' </font>For all items in this section (Zeus, Hubs, Power Supplies):
+*They typically get installed into a group24/Marine battery box from walmart.
+*Place PS in the bottom and then mount the board across the top usually mounted using the DIY method of your choice.
+*Seal up any vent holes on the top of the box.
+*[http://www.walmart.com/ip/Schumacher-Marine-Battery-Box/16550324 Example] but be free to adapt to your needs.
 |}
@@ Line 376: / Line 477: @@
 |'''16-Port Passive'''
 |'''4-Port Passive'''
+|'''Pixelnet Splitter'''
 |-
@@ Line 381: / Line 483: @@
 |Yes
 |Yes
+|No
 |No
@@ Line 387: / Line 490: @@
 |Yes
 |Yes
+|No
 |No
@@ Line 394: / Line 498: @@
 |No
 |No
+|Yes
 |-
 |'''DMX Out'''
 |Yes
+|No
 |No
 |No
@@ Line 405: / Line 511: @@
 ===='''Pixelnet Controllers Smart and Dumb'''====
+''See [[SSC_Comparison|SSC Comparison Table]] for details on SSC/Zeus cable lengths and version differences.
 {| cellpadding="15" cellspacing="0" border="1"
 |-
@@ Line 411: / Line 518: @@
 *[[SSCUse| Function & Use]]
 *[[Manual SSC|Assembly Manual v1]]
-*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=db8acde08c Mouser Direct]
+*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=56a7eec8aa Mouser Direct]
 *Max 4 amps
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
@@ Line 442: / Line 549: @@
 *[[SSC2Use| Function & Use]]
 *[[Manual_SSC2|Assembly Manual v2]]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c5920dab12 Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=086ed8e7dc Mouser Direct]
 *Max 4 amps
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
@@ Line 465: / Line 572: @@
 '''To configure SSC''' [http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=6366 SS Utility]
-:<font color="red">'''NOTE: Do not use version 1 firmware on version 2 hardware. Doing so may damage the PIC.'''</font>
+<font color="red">'''NOTE 2: Do not use version 1 firmware on version 2 hardware. Doing so may damage the PIC.'''</font>
-|width="25%"|<center>'''Smart String Controller V3'''</center>[[Image:rr.jpg|right|thumb|160px]]
+|width="25%"|<center>'''Smart String Controller V3'''</center>
-*[[SSC3Use| Function & Use]]
+*PCB never released to the members. (skipped over to SSC V4)
-*[[Manual_SSC3|Assembly Manual v3]]
+*Only the firmware released for mods on the SSCv1 & SSCv2
-*[ Mouser Direct]
-*Max 4 amps
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
@@ Line 487: / Line 592: @@
 |ED60
 |-
-|[http://diylightanimation.com/index.php?action=dlattach;topic=9490.0;attach=9392 Test]
+|[http://diylightanimation.com/index.php?action=dlattach;topic=9752.0;attach=9829 Test]
-|B4A3
+|2180
-|B51B
+|21F8
 |}
@@ Line 499: / Line 604: @@
 The updated EXE file for the utility. Just find your folder that your SSC utility is in and replace the old one with this [http://diylightanimation.com/index.php?action=dlattach;topic=9752.0;attach=9716 new file.] When you run it then you should see the additional choice for grouping on the utility.
-|width="25%"|<center>'''Dumb String Controller'''</center>[[Image:dsc-15.jpg|right|thumb|160px]]
+|width="25%"|<center>'''Smart String Controller V4'''</center>[[Image:SSCv4-Finish.jpg|right|thumb|160px]]
-*[[DSCUse| Function & Use]]
+*[[SSC4Use| Function & Use]]
-*[[Manual_DSC|Assembly Manual]]
+*[[Manual_SSC4|Assembly Manual v4]]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=c1541bd77b Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=08cdf83d9b Mouser Direct]
 *Max 4 amps
-*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24F04KA200]
 {| cellpadding = "2" cellspacing="2" boarder = "1"
@@ Line 515: / Line 620: @@
 |-
-|[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=9627 Standard]
+|[http://diylightanimation.com/index.php?action=dlattach;topic=11559.0;attach=11559 Standard]
-|8DA7
+|D8D3
-|8E1F
+|D8D3
-|}
-'''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
 |-
+|[ Test]
+|XXXX
+|XXXX
+|}
-|colspan="2"|<center>
+<font color="red">'''NOTE: Different PIC, Firmware is NOT COMPATIBLE with pervious versions of the SSC.'''</font>
+<br>
+'''NOTE 2:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
+<br>
+'''To configure SSC''' [http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=6366 SS Utility]
+<br>
+<br>
+The updated EXE file for the utility. Just find your folder that your SSC utility is in and replace the old one with this [http://diylightanimation.com/index.php?action=dlattach;topic=9752.0;attach=9716 new file.] When you run it then you should see the additional choice for grouping on the utility.
-== '''SSC v1 & v2 Mod''' ==
+|-
-</center>
+|colspan="2"|<center> '''SSC v1 & v2 Mod''' </center>
 On the following image you will see two colored in lines I painted on to an image of the top of a SSC.  This mod was designed to be totally on the top of the PCB to allow those with their SSC’s already enclosed in the PVC to do this easily. Just slide the PCB up out of the PVC as if you were going to update the firmware which you are going to do also.
@@ Line 535: / Line 649: @@
 [[Image:ssc-mod.jpg|550px]]
-Then on the back of the PCB place a jumper wire where the Yellow line is drawn. Connect these points with a small light wire making sure it does not short anything else. Remember to take into account that when you flip the PCB over to do this that everything  is mirror imaged on you.  Once this is complete you may want to change the top resistor to in the range of 220 - 330 ohms. It will work with others that we have used but you will find this to be the best area to use.  330ohm is the one to use if you are building new.
+Then on the back of the PCB place a jumper wire where the Yellow line is drawn. Connect these points with a small light wire making sure it does not short anything else. Remember to take into account that when you flip the PCB over to do this that everything  is mirror imaged on you.  Once this is complete you may want to change the top resistor (V1 pcb is marked as 330, V2 is marked as 47) to in the range of 220 - 330 ohms. It will work with others that we have used but you will find this to be the best area to use.  330ohm is the one to use if you are building new.
 Flash your SSC with the new [http://diylightanimation.com/index.php?action=dlattach;topic=9752.0;attach=9714 firmware.] The same firmware now works on both controller versions.
@@ Line 542: / Line 656: @@
 RJ
+|valign="top"|<center>'''Dumb String Controller'''</center>[[Image:dsc-15.jpg|right|thumb|160px]]
+*[[DSCUse| Function & Use]]
+*[[Manual_DSC|Assembly Manual]]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=d1779780e0 Mouser Direct]
+*Max 4 amps
+*[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
+{| cellpadding = "2" cellspacing="2" boarder = "1"
+|-
+|rowspan="2"|'''Firmware'''
+|colspan="2" align="center"|'''Checksum'''
+|-
+|width="10%"|'''Pickit2'''
+|width="10%"|'''Pickit3'''
+|-
+|[http://diylightanimation.com/index.php?action=dlattach;topic=3554.0;attach=9627 Standard]
+|8DA7
+|8E1F
+|-
+|[http://diylightanimation.com/index.php?action=dlattach;topic=11646.0;attach=11458 Test]
+|8A47
+|8ABF
+|}
+|
 |}
 =='''DMX Section'''==
-===DMX Info===
+==='''DMX Info'''===
-====[[ Hooking up a DMX Universe]]====
+====[[Hooking up a DMX Universe]]====
 * Hookup Diagrams showing DMX devices connected to a computer.
@@ Line 554: / Line 693: @@
 ===='''Controller (Dimmers) Comparison Table'''====
+|}
 {| border="1"
@@ Line 670: / Line 811: @@
 |-
 |[http://diylightanimation.com/index.php?action=dlattach;topic=2641.0;attach=4305 Test]
-|xxxx
+|767D
-|xxxx
+|76F5
 |}
+*Manual set channel = 2800
+*Must use Hexadecimal numbers
+*Example Start Channel 350 set Memory Location 2800 = 015E
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
 *[http://diylightanimation.com/index.php?action=dlattach;topic=2641.0;attach=3904 Parts Legend]
@@ Line 687: / Line 830: @@
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
 *[[media:a2-template.pdf|Aether II Template (PDF)]]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=41f67017d7 Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=363c088ded Mouser Direct]
-*[http://search.digikey.com/scripts/DkSearch/dksus.dll?WT.z_header=search_go&lang=en&site=us&keywords=LM2941T%2FNOPB-ND&x=21&y=24 Voltage Regulators (need 4)]
 *Lens
 :[http://www.mouser.com/Search/ProductDetail.aspx?R=LLSP-3T08-Hvirtualkey62410000virtualkey897-LLSP3T08H 15 deg]
@@ Line 710: / Line 853: @@
 |-
-|[http://diylightanimation.com/index.php?action=dlattach;topic=6583.msg100497#msg100497 Test]
+|[http://diylightanimation.com/index.php?action=dlattach;topic=6583.0;attach=7246 Test]
-|xxxx
+|78DD
-|xxxx
+|7955
 |}
+*Manual set channel = 2800
+*Must use Hexadecimal numbers
+*Example Start Channel 125 set Memory Location 2800 = 007D
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
@@ Line 736: / Line 881: @@
 ** [http://www.diylightanimation.com/Express_V4_Manual_Part_1.wmv Part 1]
 ** [http://www.diylightanimation.com/Express_V4_Manual_Part2.wmv Part 2]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=e19c8724ea Mouser Direct]
+*'''NOTE:''' SAA1064 on BOM is no longer available; it must be sourced from eBay or the secondary market
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=9ece605bc0 Mouser Direct]
 *[[Graphics#.23Express|Graphics]]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
@@ Line 758: / Line 904: @@
 *[http://diylightanimation.com/index.php?action=dlattach;topic=1128.0;attach=846 Config Utility]
 *[[LNT_Light_Curves|List of Light Curves]]
-*[http://diylightanimation.com/wiki/index.php?title=LE_Trouble Trouble shoot]
+*[http://diylightanimation.com/wiki/index.php?title=LE_Trouble Troubleshoot]
 |width="25%"|<center>'''Lynx Freestyle'''</center>[[Image:FreeStyle-1.jpg|right|thumb|160px|128 Channel Controller only]]
@@ Line 780: / Line 926: @@
 |}
+*Manual set channel = EEPROM Data Area = Memory Location 02 & 04
+*Must use Hexadecimal numbers
+*Example 100 = 0X64 set Memory 02 = 64 and Memory 04 = 00
+*Numbers over 255 must be split
+*Example 410 = 0X19A set Memory 02 = FF and Memory 04 = 9B
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
@@ Line 788: / Line 938: @@
 *[[Manual MR16|Assembly Manual v2]]
 **[[Manual MR16_v1|Previous Manual]]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=b7accb974d Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=73d1b6935b Mouser Direct]
 *[[Graphics#.23MR16|Graphics]]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F1220]
@@ Line 803: / Line 953: @@
 |90D4
 |90D4
+|-
+|[http://diylightanimation.com/index.php?action=dlattach;topic=3425.0;attach=4057 Low Power]
+|A07D
+|A07D
 |}
+*Manual set channel = A00
+*Must use Hexadecimal numbers
+*Example Start Channel 312 set Memory Location A00 = 0138
+*Size = 4.25" x 4.75" x 1.25"
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
@@ Line 814: / Line 972: @@
 *[[Arch_SSR4|Previous Assembly Manual]]
 *Mouser Direct
-**[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=8291b59919 Base SSR4]
+**[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=da4879a3c9 Base SSR4]
-**[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=3c898b8cf2 DMX Option]
+**[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=f8d320ca8c DMX Option]
-**[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=5250caa9af SSR4 with DMX]
+**[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=e26265f32c SSR4 with DMX]
 *[[Graphics#.23SSR4|Graphics]]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F1220 (SSR4 with DMX version)]
@@ Line 833: / Line 991: @@
 |}
+*Manual set channel = A00
+*Must use Hexadecimal numbers
+*Example Start Channel 32 set Memory Location A00 = 0020
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
 |}
@@ Line 886: / Line 1,046: @@
 |}
-*[http://diylightanimation.com/index.php?action=dlattach;topic=3712.0;attach=4394 Firmware 12-12-2010]
-:'''Checksums'''
-:Pickit2 - 1AED
-:Pickit3 - 1B65
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
 * [[Mod_Wireless|Mod for other Controllers]]
@@ Line 904: / Line 1,060: @@
 *[[Dongle_Manual_v2|Assembly Manual v2]]
 **[[Arch_Dongle|Previous Manuals]]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=9eeb022092 Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=3e72e3c7a8 Mouser Direct]
 *[[Graphics#.23Dongle|Graphics]]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F2450]
@@ Line 930: / Line 1,086: @@
 *[[Manual Splitter|Assembly Manual v3]]
 **[[Manual Splitter_v1|Previous Manual]]
-*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=d5418a6654 Mouser Direct]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=7f9e50e3a7 Mouser Direct]
 *[[Graphics#.23Splitter|Graphics]]
 *240v Transformer Digikey's p/n 567-1019-ND
@@ Line 937: / Line 1,093: @@
 *[[Manual Tester|Manual]]
 *[http://vimeo.com/23517936 Build Video]
-*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=8ABF3AEFB2 Mouser Direct (Tester)]
+*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=cffe4f9f5a Mouser Direct (Tester)]
-*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=0a8146d89a Mouser Direct (Wireless Tx)]
+*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=71fa19c314 Mouser Direct (Wireless Tx)]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F24J10-I/SP (Tester)]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002 (Wireless)]
@@ Line 949: / Line 1,105: @@
 |width="25%"|<center>'''Bobcat DMX Servo Controller'''</center>[[Image:ServoController.jpg|right|thumb|160px]]
 *[[Manual Servo|Manual]]
-*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=F5E3BD8F09 Mouser Direct]
+*[http://www.mouser.com:80/ProjectManager/ProjectDetail.aspx?AccessID=3548b3495d Mouser Direct]
 *[http://diylightanimation.com/index.php?action=dlattach;topic=4835.0;attach=6825 Firmware]
 *[http://www.diylightanimation.com/wiki/images/8/8f/Bobcat_Servo_Schematic.pdf Schematic]
 *[http://diylightanimation.com/index.php?action=dlattach;topic=4835.0;attach=7108 Configuration Tool]
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC18F23K20-I/SP]
+|-
+||<center> '''Panther DMX Player''' </center>[[Image:PantherDLA.png|right|thumb|160px]]
+*[[Manual Panther DMX Player|Assembly Manual]]
+*[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=f234770183  Mouser Direct]
+*[http://www.ebay.com/sch/i.html?_sacat=0&_from=R40&_nkw=SD+Card+Module&_sop=15  eBay SD Card Module]
+*[http://dl.dropboxusercontent.com/u/58620146/PantherDMXPlayer/Panther%20DMX%20Player%20Cut%20Outs.pdf Enclosure Cutting Template]
+*[http://dl.dropboxusercontent.com/u/58620146/PantherDMXPlayer/PantherDMXPlayerV200.hex Firmware V2]
+<font size="2" color="red">NOTE: Only use V2 firmware on V2 boards. </font><br>
+'''NOTE:''' To download firmware right click on it and choose save as.
+|
+|
+|
 |}
@@ Line 962: / Line 1,131: @@
 *Parts Ordering:
 **[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=7A775E9B7D '''Mouser Direct''']
-**[http://www.newark.com/maxim-integrated-products/ds32khz-dip/ic-crystal-osc-32-768khz-5-5v-14/dp/74C2865?Ntt=DS32KHZ/DIP '''Order (1) of this part''']
+**[http://www.digikey.com/product-detail/en/DS32KHZN%2FDIP/DS32KHZN%2FDIP-ND/420269 '''Order (1) of this part''']
 **'''PCB from RJ'''
 *[http://www.diylightanimation.com/wiki/index.php?title=J1SYS_boards_jumper_chart PIC24FJ32GA002]
@@ Line 991: / Line 1,160: @@
 *[[Manual Lynx|Assembly Manual]]
 *[http://diylightanimation.com/index.php?action=dlattach;topic=377.0;attach=743 Firmware] 9E83
+*Manual set channel = A00
+*Must use Hexadecimal numbers
+*Example Start Channel 61 set Memory Location A00 = 003D
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
@@ Line 1,000: / Line 1,172: @@
 *[http://diylightanimation.com/index.php?action=dlattach;topic=3288.0;attach=3574 Firmware compat w/v2]
 :'''Checksums'''
-:Pickit2 - xxxx
+:Pickit2 - 46E6
 :Pickit3 - 475E
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
@@ Line 1,011: / Line 1,183: @@
 *[http://diylightanimation.com/index.php?action=dlattach;topic=3288.0;attach=3573 Firmware compat w/v2]
 :'''Checksums'''
-:Pickit2 - xxxx
+:Pickit2 - 5E72
 :Pickit3 - 5EEA
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
@@ Line 1,023: / Line 1,195: @@
 *[http://diylightanimation.com/index.php?action=dlattach;topic=3288.0;attach=3573 Firmware compat w/v2]
 :'''Checksums'''
-:Pickit2 - xxxx
+:Pickit2 - 5E72
 :Pickit3 - 5EEA
 '''NOTE:''' Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
 |}