Difference between revisions of "Enttec Pro Connections"
From Holiday Controller
Aussiephil (Talk | contribs) (New page: Based on a question from the forums *I'm at a roadblock!! Got my first of four Lynx built, I have my Pro dongle, but thats where the pavement ends.. Can someone post how does the Pro get...) |
Aussiephil (Talk | contribs) |
||
| Line 3: | Line 3: | ||
*I'm at a roadblock!! Got my first of four Lynx built, I have my Pro dongle, but thats where the pavement ends.. Can someone post how does the Pro get wired? The Lynx manual says Lynx Cat5 pins 1, 2 get wired to DMX's pins 2, 3.. well, I identified pins 2, 3 on the DMX Pro, but which jack, the DMX IN or OUT? On the Cat5 cable, which are pins 1, 2? Can someone ID Cat5 pins 1, 2 by the color pairs? Pictures.. anyone got pictures of theirs? | *I'm at a roadblock!! Got my first of four Lynx built, I have my Pro dongle, but thats where the pavement ends.. Can someone post how does the Pro get wired? The Lynx manual says Lynx Cat5 pins 1, 2 get wired to DMX's pins 2, 3.. well, I identified pins 2, 3 on the DMX Pro, but which jack, the DMX IN or OUT? On the Cat5 cable, which are pins 1, 2? Can someone ID Cat5 pins 1, 2 by the color pairs? Pictures.. anyone got pictures of theirs? | ||
| − | The [http://www.enttec.com/datasheets/70304/DMXUSBPro.pdf |Datasheet for the Pro]is at the Enttec website | + | *The [http://www.enttec.com/datasheets/70304/DMXUSBPro.pdf |Datasheet for the Pro]is at the Enttec website |
| − | This [http://freespace.virgin.net/tom.baldwin/pinout-5xlr.html Website] shows the pinouts for the 5 pin XLR | + | *This [http://freespace.virgin.net/tom.baldwin/pinout-5xlr.html Website] shows the pinouts for the 5 pin XLR |
| + | **Pin 1 = Ground | ||
| + | **Pin 2 = Signal -ve | ||
| + | **Pin 3 = Signal +ve | ||
| + | **These pin numbers are true for both 5-pin and 3-pin connectors, although strictly speaking 3-pin connectors should not be used as they don't comply with the official DMX512 standard. | ||
| − | |||
| − | From the Enttec Pro Dongle you would use the Out connector, the input is optional use. | + | *For [http://en.wikipedia.org/wiki/Category_5_cable CAT 5 Pinouts] Wikipedia has a great little article and pictures. |
| + | |||
| + | *From the Enttec Pro Dongle you would use the Out connector, the input is optional use. | ||
[[Main Page]] | [[Main Page]] | ||
Revision as of 10:47, 23 April 2008
Based on a question from the forums
- I'm at a roadblock!! Got my first of four Lynx built, I have my Pro dongle, but thats where the pavement ends.. Can someone post how does the Pro get wired? The Lynx manual says Lynx Cat5 pins 1, 2 get wired to DMX's pins 2, 3.. well, I identified pins 2, 3 on the DMX Pro, but which jack, the DMX IN or OUT? On the Cat5 cable, which are pins 1, 2? Can someone ID Cat5 pins 1, 2 by the color pairs? Pictures.. anyone got pictures of theirs?
- The |Datasheet for the Prois at the Enttec website
- This Website shows the pinouts for the 5 pin XLR
- Pin 1 = Ground
- Pin 2 = Signal -ve
- Pin 3 = Signal +ve
- These pin numbers are true for both 5-pin and 3-pin connectors, although strictly speaking 3-pin connectors should not be used as they don't comply with the official DMX512 standard.
- For CAT 5 Pinouts Wikipedia has a great little article and pictures.
- From the Enttec Pro Dongle you would use the Out connector, the input is optional use.
