Difference between revisions of "Equipment"
From Holiday Controller
(→'''DMX Devices''') |
(→'''Aether''': added bom links) |
||
| Line 290: | Line 290: | ||
*[[Manual_AetherII|Manual]] | *[[Manual_AetherII|Manual]] | ||
*[[media:a2-template.pdf|Aether II Template (PDF)]] | *[[media:a2-template.pdf|Aether II Template (PDF)]] | ||
| − | *Mouser Direct | + | *[http://www.mouser.com/ProjectManager/ProjectDetail.aspx?AccessID=41f67017d7 Mouser Direct] |
| + | *[http://search.digikey.com/scripts/DkSearch/dksus.dll?WT.z_header=search_go&lang=en&site=us&keywords=LM2941T%2FNOPB-ND&x=21&y=24 Voltage Regulators (need 4)] | ||
*Graphics | *Graphics | ||
*[http://vimeo.com/24755871 '''Aether II Prototype Demo'''] | *[http://vimeo.com/24755871 '''Aether II Prototype Demo'''] | ||
Revision as of 14:50, 10 November 2011
Contents
Hooking up a DMX Universe
- Hookup Diagrams showing DMX devices connected to a computer.
Equipment Errata
- This page is for mods needed on released production boards from DLA.
Controller (Dimmers) Comparison Table
| Controller | DMX | # Channels | On Board SSR | Wireless Pkg | LNT | Dimming | On Board Splitter | 12v DC | 120v AC | 240 AC |
| Lynx Express | Yes | 16 | Yes | EX/RX or RX | Yes | Yes | Yes (1)** | No | Yes | Yes |
| Lynx Freestyle | Yes | 128 | No/SSR4 | EX/RX wMod or RX | No | Yes | No | No | Yes | Yes |
| Lynx SSR4-DMX | Yes | 4 | Yes | EX/RX wMod or RX | No | Yes | No | No | Yes | No |
| Lynx MR-16 | Yes | 16 | LED/MR16 | EX/RX wMod or RX | No | Yes | No | Yes *** | No | No |
- Legend
- LNT = Light Normalizing Technology. With the proper curves all lights turn on and dim at the same rate.
- Need to know if Lynx hardware works in your region? Lynx Voltage Info
- Asterisk Notes
- ** Two DMX outputs using wired input (Cat5) with ver 3 pcb and higher or
- One DMX output (DMX Out2) if using the mounted EX/RX wireless module on ver 3 pcb and higher
- *** MR16 is capable of handling up to 24 volt DC source power. Please place a heat sink on the 5 volt regulator.
Cases Chart
| Lynx Device | Case Part# | Info | Purchase Info |
|
CG-1500 | Coax Demarcation Enclosure
|
|
16 Channel DC Controller |
CG-500 | Coax Demarcation Enclosure
|
|
|
TA-200 | Coax Demarcation Enclosure
|
|
|
LP-35P | Choose Gray and put in the comments of the order
|
If you call they will ship USPS at a much cheaper rate than UPS |
|
LP-51P | Choose Gray and put in the comments of the order
|
If you call they will ship USPS at a much cheaper rate than UPS |
Smart Strings
Smart String / Pixelnet Library
| Documents | |
Videos
|
|
Software
|
|
| Diagrams | |||
 |
 |
 |
 |
| Light type | Input Side | Max # per SSC
|
Approx Amps
|
Links to purchase online
| ||||
Smart String Nodes
|
Big Chip Side of Node | 3.7975
|
25ct String
|
50ct String
|
75ct String
|
100ct String
|
128ct String
| |
(Metal Backed) 3 50/50 Nodes
|
3.96
|
Square | ||||||
(Plastic rectangle) 50/50 Nodes
|
DI | 4.16
|
Rectangle | |||||
Rigid strips 30 50/50 Nodes
|
Male 3 pin connector | Not Known Yet | Rigid | |||||
Flexible strips 13ft 50/50 nodes
|
Arrows show direction | approx 3.96
|
Flexible | |||||
| Accessories | 3 Conductor Cable | 3 Conductor Connectors | ||||||
Pixelnet Hardware
NOTE: Only use the Pickit 3 utility and not MPLAB to program the firmware |
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
|
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
|
Aether
DMX LED RGB(W) Flood/Spot Light
Pronunciation on Aether:
- Ether \E"ther\ ([=e]"th[~e]r), n. [L. aether, Gr. a'iqh`r, fr. a'i`qein to light up, kindle, burn, blaze; akin to Skr. idh,
- indh, and prob. to E. idle: cf. F. ['e]ther.] [Written also [ae]ther.]
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
|
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
|
Dimmers
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware
|
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
DMX Wireless Devices
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
DMX Devices
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
|
 |
|
Aeon Clock
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
Discontinued Hardware
 NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware | ||
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
NOTE: Only use the Pickit (2 or 3) utility and not MPLAB to program the firmware |
